How to Drill Glass

Here is how to quickly and easily drill holes in glass.  In fact, you can drill a 1″ hole in a 10 gallon aquarium in under 3 minutes from start to finish!  I’ve tried several methods and the method I describe here is by far the fastest and easiest.  Skip to the video.

Do not try to drill into tempered glass.  Trust me, I found out the hard way.  Some larger sized aquariums use tempered glass on the bottom so check before you drill.  There is a chance you will break the glass even if it is untempered so I suggest you practice first, if possible, and always wear safety goggles!

You will need an electric hand drill.  Cordless drills are easier to work with in my opinion.  Make sure you can control the speed of the drill precisely.  I have a cheap corded drill that I have a hard controlling the speed with and I broke an aquarium because I drilled too fast.  You will also need a special drill bit.  Large hardware/home stores sell pointed drill bits for use on tile.  These may work, but I’ve never tried them.  I suggest you get a good diamond coated drill bit.  They are more expensive than the pointed tile bits but worth it.  Let me say that again, get a GOOD diamond coated drill bit!  You can find them online.  My 1″ bit cost about $30.  I think I got mine from here, but I can’t remember.  I recently (11/6/2011) bought one at my local Menards and they had a decent selection of sizes. More recently (1/17/2015), I saw a nice selection at my local Lowes. You can also buy sets pretty cheapy on Amazon these days:

Set of 5 (up to 1″) – http://amzn.to/1AOIbTW
Set of 5 (up to 1/2″) – http://amzn.to/1Cdd4WC
Set of 5 (up to 1 1/2″) – http://amzn.to/1AOJhim

Diamond drill bit
Diamond drill bit

You will also need some clay.  I use cheap children’s modeling clay from the craft store.  You don’t need much and as long as it doesn’t dry out, it will last a long time.  Here is the video demonstration of how to drill glass in under 3 minutes:


The first thing to do is to form the modeling clay into a wall around the spot you will drill.  Try to make a good seal between the clay and the glass.  Tiny leaks shouldn’t make much difference but your well should be able to hold water for several minutes.

Ring of Clay
Form a wall around your spot with modeling clay.

Fill the well with water.  You want to make sure your drill bit stays wet at all times.  Most glass drill bits have little holes in them.  Make sure water can flow into these holes to cool and lubricate the inside of the drill bit.  Start to drill at an angle.  This will help the bit bite into the glass and will prevent the bit from sliding around as you continue to drill.  The most important thing to remember while drilling glass is to go slowly! Keep the drill at a slow speed at all times.  If you go to fast, you will crack the glass.

Start of drilling
Start to drill at an angle.

Once you have drilled an arch in the glass, slowly angle the drill bit into a vertical position while continuing to drill.  Your starting arch should hold the bit into place as you tilt the drill up.  Continue to drill.  I like to pour freshwater into the well when the water gets cloudy.  This keeps the temperature down and makes it easier to watch my progress.

Dirty water
Add freshwater when the old water gets cloudy.

When you get close to the end, slow down your drill even more.  This will help prevent the edge of the hole from chipping.  When you get all the way through the glass, the bottom of the hole will drop out and the water in your well will quickly drain in a most satisfying way.  Clean up the mess and you are done! Back to the video.

Finished hole
The finished hole. There is a little chipping around the edge but nothing to be too concerned about.

12 thoughts on “How to Drill Glass”

  1. For a person who is not a professional, buying a diamond drill bit is waste of money for small jobs. In India, even shops doing glass selling business do not have such diamond drilling bits.

  2. A 1/2″ bit will cost about $20. A 1″ will cost about $30. If you only need to make 1 hole, this might not be cost effective. If you are drilling multiple tanks or drilling an otherwise expensive tank, then $20-30 isn’t that expensive.

  3. It works as demonstrated which is what matters and who wants to keep buying new glass until you get it right. Thanks for the clip.

  4. Amazing guy!!! I’ve been searching this kind of video.bec.i have a 1/2 inch thick glass table I wanna put hole.

  5. Hi!
    Just wondering if you can give me some tips on how I would drill a hope through a glass jar, and then attach it securely to a wall.
    Thanks!

  6. Drilling the jar shouldn’t be too bad. You’ll just want to find a way to hold the jar still while you drill. A vise with light pressure might work. Hand holding might work too if you are careful and wear protective gloves.

    I came up with one idea off the top of my head for attaching it to a wall. You’ll need a screw or bolt, 2 metal washers, 2 rubber washers, and possibly some sort of wall anchor (depending on what the wall is made of). You’ll want the rubber washers touching the glass and the metal washers between the rubber ones and the screw and wall. The tricky part will be tightening the screw/bolt. A short screwdriver might work. If you can find a bolt with a hex head, you could use pliers or a rachet. You’ll also have to be careful not to overtighten and break the glass. Here’s a quick sketch (not to scale):
    Jar Wall Idea

  7. It’s hard to find your website in google. I found
    it on 11 spot, you should build quality backlinks , it will help
    you to increase traffic. I know how to help
    you, just search in google – k2 seo tricks

  8. I read a lot of interesting articles here. Probably you
    spend a lot of time writing, i know how to save you a lot of time, there is an online tool that creates unique, SEO friendly posts in minutes, just type in google – laranitas free content

Leave a Reply

Your email address will not be published.

Where I make and modify stuff